Tag: knife

Posted on

The Knife Buyer’s Inspection List; 6 Things to Check When You Receive a New Knife

So, you just bought yourself a shiny new knife and want to make sure it’s up to snuff. In this article I’ll describe the 6 points that I check when receiving a knife. These characteristics cover the bulk of what decides where a knife lands on the spectrum from abysmally terrible to mythically epic.

#1 Edge Exposure

Checking for edge exposure, most commonly in the form of a proud tip, is one of the first things I do when inspecting a knife. This is because it is a practical concern; if the edge is exposed you can accidentally cut yourself when reaching in your pocket for the knife etc. Most commonly on slipjoints, but also sometimes on modern knives, this issue rears its ugly head as a proud tip. A tip is proud when it sits above the blade well enough that it can be caught on a fingernail without actually opening the blade. This issue is all too common in my opinion, and those who watch my videos know I am hounded by proud tips on otherwise perfect GECs. Modern knives can also have proud tips, but I find it to be quite uncommon. However, modern knives, often having pass through handles (no backspring / a gap at the spine side of the blade well also), can sometimes have edge exposure along that spine side of the handle. This happens when the blade is too tall for the blade well and the edge sits close enough to the back of the handle that you can contact it when running a finger along the back of the handle. Both of these types of edge exposure have their fixes; a proud tip can often be alleviated by dropping the kick, and the edge can be sharpened back from the handle opening. However, I prefer not to have to modify my knives for them to be safe (even if actual injury is unlikely) so these issues are sometimes deal breakers.

#2 Edge Damage

Edge damage on a new knife is most commonly caused by blade rap, but can also be a defect in sharpening. Blade rap is when the edge hits some part of the handle upon closing. On slipjoints the edge often hits the backspring, especially at the spring pin hump, and on modern knives the edge sometimes hits the backspacer or a standoff. I would also consider the edge hitting the sides of the blade well blade rap, but that is covered more in depth by the next point. The edge hitting the backspring can cause varying levels of damage to the edge, from a barely perceptible flat area to a full on roll. No matter the amount of damage done, blade rap diminishes the utility of the knife and is a defect. That said, note that some traditional knife patterns, notably from France, are designed to have the edge rest on the backspring so as to eliminate the tip becoming proud through multiple sharpenings. Less commonly, some knives might come with edge damage not related to blade rap. This type of edge damage can be due to a poor sharpening job from the factory or from damage in shipping. As a knife’s purpose is to cut, the edge should arrive to the buyer without damage.

#3 Blade Centering

The title pretty much says it all here; is the blade centered in the blade well? Some people put a lot of emphasis on this point because they strongly prefer the aesthetics of a centered blade, which is fine if that matters to you. However, an uncentered blade can be indicative of other issues such as blade play (discussed in the next point), a bent or unevenly ground blade, or a warped handle. Those are more practical issues rather than aesthetic. Of course, if a blade is so off centered that it rubs on the handle liners or actually hits the edge on the liner upon closing that is a definite defect. The blade should not be defaced or the edge damaged every time the knife is closed.

#4 Lockup

Most modern folding knives lock, and the lock should function securely when received. The lock should hold the blade open without significant play, or movement, in any direction (for most lock types). You can test for blade play by opening the knife then grasping the blade from the spine side, being careful to keep your hand far from the edge, and try to wiggle the blade side to side and forward and back. Another test that many do is a spine whack test. A spine whack test is when you strike the spine of the locked blade against a hard surface, such as a piece of wood, to check that it doesn’t unlock. Many manufacturers discourage this test, and it is a test that should be done with the utmost care and emphasis on safety (NEVER hold the knife so your hand is in the way of the blade if it did fold) if done at all. Of course, non locking knives can’t be tested for lockup but you can still test for side to side blade play. Having secure lock up is an important aspect of a good knife, as poor lockup can range from irritating to downright dangerous.

#5 Action

Action is the term used for the actual opening and closing of a knife. Folding knife action has come a long way in the last decade or two. Now even extremely budget friendly knives often come with glassy smooth opening and closing. Many knives have ball bearing washers in their pivots which allow for very low friction. Some look for “drop closed smooth” meaning that the blade drops closed by its own weight when unlocked, while others prefer a more deliberate closing motion be required. What an ideal action looks like is up to each individual, but I think a knife’s action should both work practically and be enjoyable.

#6 Fit and Finish

Finally, the knife should be inspected for general fit and finish. So what is fit and finish? It’s the sum of how precisely the parts of the knife are fit together and how well each part is finished. This could include the meeting of the scales, or covers, of the handle with the bolsters or with the liners. It could include the evenness of the finish on the handle and blade; the lack or presence of machining marks etc. Fit and finish is another area where budget knives have made huge strides to close the gap with premium knives over the last few years. Most modern knives of $50 and up should have few if any obvious imperfections in the fitment of the parts and finish of the surfaces upon a cursory glance. That said, some knives are expected to have slight imperfections due to the nature of their manufacture. For example, many traditional slipjoint knives are expected to have minor flaws and individual character because they’re made using traditional methods. Even Great Eastern Cutlery, the premier American traditional knife manufacturer, knives are expected to have a slight deformation in a pin or gap around the shield every now and then. Ultimately, the level of fit and finish that one finds acceptable at each price point is a personal decision, but it is still worth considering.

BONUS; First Impression

There’s another characteristic of a knife that I think is worth considering but that didn’t make the list; the visceral first impression it gives you. Often, as a knife enthusiast, opening a knife and handling it for the first time will give you a strong feeling. Whether positive or negative, this feeling often has nothing to do with the objective qualities of the knife outlined above. Even though this first impression might not be based on any real practical characteristics, it’s still important to one’s enjoyment of a knife. We as knife enthusiasts deserve to be thrilled every time we get a new knife, so don’t ignore your first impression of a new purchase.

For those of us who make knives a hobby, we deserve to get a good value for our hard earned money. That’s why I think it’s important to check each knife you receive for these 6 key points of quality, and also to consider your first impression. If a knife passes all these checks, congratulations; you have yourself a great every day carry tool or collection piece in your new knife!

P.s. I used videos that touch heavily on the discussed characteristic here in lieu of pictures because I think they do a better job of showing the issue in a realistic manner.

I sincerely thank you for your time, support, and interest! Don’t forget to tell your friends about KnifeThoughts.com, subscribe via email, and share this article on social media. You can find Knife Thoughts on YouTube where I have hundreds of knife videos, as well as on Instagram and Facebook! You can find all my latest links at LinkTr.ee/KnifeThoughts

Posted on

Head VS Heart; To Collect or to Use Your Knives

The question of what the “right way” to express enthusiasm for knives is one that shouldn’t need answered. I find it silly and overbearing for anyone to suppose that they should or can tell another the best way to enjoy a hobby. Still, I have gone through several phases in regard to the idea of keeping knives as collection pieces in contrast to keeping them as using tools, and I think others have had similar shifts in perspectives. In this post I’ll describe my progression through those stages and how my current collection looks… but no guarantees it won’t change again!

A tasteful knife display, the stand a gift from my fiancee

I, like many, started with having only one knife that I used for everything. I didn’t even really consider the idea of having knives as collection pieces, and probably would have scoffed at the idea had it been suggested. Still, I was what I would consider a knife enthusiast though, as I appreciated the knife not just as a tool but as a piece of mechanical workmanship that elevated man’s most ancient tool to a higher level. I think there is a silent but quite large population of people who fit this category; they appreciate a good knife and see it as more than a disposable tool, but they don’t venture further into the hobby with more knives and deeper research.

I store my modern knives in a cheap single layer tackle box
Most of my modern knives, all users to varying degrees

A desire to know more about a particular knife brought me to the next step in the knife hobby. I don’t remember exactly what I was looking up, but in the process I found BladeForums and my eyes were opened to the wide world of the knife hobby. As I read, watched, and listened I grew more knowledgeable on knives, the knife making process, and the knife community in general. At this stage I began to purchase more knives beyond one user, but the number stayed relatively low and all were used regularly. I think this represents another distinct stage in the knife enthusiast scale, as it is a step out of appreciating knives as an individual separate from any other enthusiasts, and into the larger knife community. I stayed at this stage for a while, buying and selling and trading knives as I learned. During this stage I never amassed a significant enough number of knives that any would go unused for long. I think this is a stage that a lot of people also stay in and don’t move deeper into the hobby from, but fewer than the previous stage.

I store most of my user traditionals, sharpening gear, and random EDC stuff in a multi layer tackle box
Some of my user traditionals

The final stage is reached when you have more than enough knives to use, but you keep buying them anyway! Often, I think people reach this stage also because they start to realize their preferences and build coherent collections. This is when knives accumulate to the point that some don’t get used. Another thing that often happens before this stage is you start to accumulate knives that are rare, have sentimental value, etc. that make them less likely to be used. This stage probably has the widest variation in expression; some people might have one knife they use all the time and 100 (or 1000) that they never use or carry at all, and some might have 100 knives that they carry and use in a rotation and only 10 (or 1) that they have as a non user collection piece. I fall somewhere on that spectrum closer to the latter end.

I store my non user knife collection in a Pelican case
Top Row:
GEC #46 Whaler AMKCA 2018 Club Knife, GEC #46 Whaler 2018 Rendezvous Special, GEC #38 Special 2017 Rendezvous Special, GEC #74 Mustang 2016 Rendezvous Special, GEC #74 Improved Trapper 2015 Rendezvous Special, GEC #15 TC One Arm Barlow 2014 Rendezvous Special
Bottom Row:
Queen Copperhead, GEC #53 Cuban Stockman, GEC #82 Dixie Stock Knife, Victorinox Spartan Costa Rica

However, I don’t believe those stages tell the whole story of knife collecting. For me, being a knife collector is about enjoying the hobby. For some people, that means having and using one knife till the wheels fall off. For others, that means buying every trendy or appealing knife that comes out and keeping them pristine. For me, it has come to mean many things. First, it means enjoying the knives I have. While I do keep some knives as pristine as possible, I try to enjoy them by displaying them and showing them at knife club meetings and shows. Other knives I enjoy by carrying and using them. I find that using a knife is the best way to enjoy it. It just feels right to use a knife as a tool, and doing so seems to confirm its value and place as the most fundamental human tool. So, why not use all my knives? For a long time, I didn’t think I had a satisfactory answer to that question. I had valuable knives, both of the monetary and sentimental type, but I thought that if I didn’t use them it was a waste to keep them. However, that led me to sell knives that I later wished I had kept (which will be the subject of another article). Now, I’ve become comfortable with the idea that some knives are better kept in good condition whether it be because they’re valuable, part of a set, or meant to be an heirloom. I have a small collection of knives I don’t use. Some of them are the Great Eastern Cutlery Rendezvous Specials. These are knives made in small numbers for the gathering GEC holds in Titusville every year and only available at the gathering. They’re usually unique knives in some way. They’ve become the main part of my non user collection, as they’re easily the most coherent and rare set of knives I have owned. I actually did use the first couple of these initially, but later decided they were better kept in good condition to form a recognizable and consistent set. I also have a Queen Copperhead that is the best Queen made knife I’ve ever seen that I don’t use because Queen has unfortunately gone out of business. I plan to add some more Queen knives to my non user collection, as I want to have some examples from Queen as one of the most historic cutlery companies in the U.S. and they’ll only get scarcer the longer its doors have been closed. I also have some knives that have been given to me as gifts from friends, family, and loved ones. Despite it seeming silly to not use knives as tools like they’re inherently intended, some knives are worth maintaining in good condition for posterity.

Great Eastern Cutlery Rendezvous Specials on the knife stand from my fiancee, top to bottom:
#46 Whaler 2018 Oily Heart Pine Wood, #38 Special LVS Paua Abalone 2017, #74 Mustang Primitive Bone 2016, GEC #74 Improved Trapper Tortoise Shell Acrylic 2015, GEC #15 TC One Arm Barlow Oil Sucker Rod Wood 2014

Thanks to my fiancee for the idea for this article and the inspiration for the title! In her words “Your heart wants to use all the knives but your head says you should keep some nice”. I can’t thank her enough.

Posted on

The Trapper Pattern; You Know It When You See It

TL;DR? Check out the companion Knife Thoughts video on my YouTube channel at this link!

This article will be less of a review of a particular knife and more of an overall look at a general knife pattern; the Trapper. The Trapper pattern has a long history and has become well known, or at least recognizable, to most Americans who are familiar with pocket knives. Whether you’re a fan of the pattern and want to know some of its history and specific characteristics or if you have no idea what a Trapper is and are picturing a knife with two spring loaded jaws for capturing small critters, this article will tell you all you all you need to know about the Trapper!

The Case Large Trapper in Yellow Synthetic is a great exemplifier of the Pattern

First, the Trapper is a pattern with a somewhat obscure history. The claim is often put forward on knife blogs and forums that it’s a pattern that’s been used since the frontier days of America when rugged mountain men trudged into the unknown mountains to live out their lonesome and hard, but proud, lives trapping for furs and fortune. Obviously, a knife pattern called the Trapper must have originated from its namesake profession. Unfortunately for the romantics out there imagining Jim Bridger and John Colter comparing their personal Trapper knives in the 1800’s, the Trapper pattern as shown above is a 20th century invention. Like many traditional knife patterns, the Trapper evolved from older types of knives into its own unique pattern in the early 1900’s during the so called Golden Age of American cutlery. In the early decades of the 20th century there was a multitude of cutlery manufacturers that were staffed by cutlers transplanted from the old European knifemaking centers of England and Germany. These companies and cutlers took many older patterns that were brought from Europe and modified them into their own unique American patterns. The Trapper is a great example of that process. The predecessor to the Trapper was probably a slim dogleg jack with about a 4″ handle and a clip point main blade and pen secondary blade. This type of knife was made as far back as the 1880’s, and sometime in the ensuing 4 decades some companies changed the pen secondary to a full length spey blade to make a slimmer version of the classic Trapper as shown above. It seems the beefier trapper with two full length blades probably didn’t appear until the 1920’s. It was probably first made by either Case or Kabar. In this period many knife manufacturers made knives to be branded and sold by other companies. Even more confusingly, many companies, including Case and Kabar, were connected through family ties. These circumstances can make it difficult to pinpoint the genesis of a particular pattern. The Trapper remained a relatively minor pattern until after WWII. Since then pretty much any knife company that makes traditional slipjoints has produced one or more variations of the Trapper pattern, and it has become a mainstay of the American pocket knife market. Speaking of variations, what exactly is (or isn’t) a Trapper?

Camillus Remington Master Guide, Case Large Trapper, Queen Utility, Rough Ryder Trapper, GEC Northfield Improved Trapper, Great Eastern Cutlery Mustang

The Trapper pattern covers a huge range of sizes, blade shape combinations, and even handle shapes. The above picture is a great example the ways in which the size and handle shape of the trapper can vary. Although the Trapper pattern developed from a slim dogleg jack (like the Queen Utility third from the left), it can also have a banana shaped frame (like the Camillus made Remington Master Guide on the far left or the GEC Northfield Improved Trapper and Great Eastern Cutlery Mustang both on the far right), and is probably best known as a beefier dogleg jack (like the Rough Ryder Trapper third from the right) sometimes with a swell on the blade well side of the handle (like the Case Large Trapper second from the left). As you can see, the Trapper’s frame can be one of several different handle shapes with variations possible even within those general shapes. Also, although they tend to stay within the 3.5″ to 4.5″ range, Trappers can land anywhere from the Case Tiny Trapper at 2.375″ closed to the Remington Master Guide at about 5.375″ closed.

Spear and Pen, Clip and Spey, Clip and Spey, Clip and Wharncliffe

The Trapper pattern can also have just about any blade shape style and combination you can imagine. However, the classic configuration is two full size blades with one being a clip point and the other being a spey blade. The clip point is a great all around blade because it offers a pointy tip (although Case knives, like the one below, often come with rounded tips), a solid amount of curved edge, and some straight edge also. The spey blade is historically designed for use in castrating animals, as the abruptly curved belly and lack of a significant tip make it a good blade for slicing and push cuts but not good at piercing (wouldn’t want to stab your livestock when they start kicking, which they will do if you’re using the spey blade for its namesake…). It’s possible that the spey blade was added for outdoorsmen (hunters and TRAPPERS, get it) to use as a skinning blade with less chance of piercing the guts, but my guess would be that it was added just as a novelty to have two full length blades and without much more specific reason than that. Still, it does make for a useful blade combination as it can be nice having two full length blades. I tend to use the spey blade for food prep and the clip point for everything else. Like the shape and size of the handle, the blade shapes on knives considered to be Trappers can go far beyond the classic clip and spey. There’s the Slim Trapper with a single turkish (slender) clip point, the Pen Trapper with a main blade that is most often a clip or drop point but can sometimes be a spey or spear point with a small/secondary pen blade, the Improved Trapper with a clip point and wharncliffe blade, and the Single Blade Trapper with one main blade (usually a clip point, but it can also be a drop, spear, or spey).

  • Clip Point blade
  • Spey blade

So, what is a Trapper knife? Considering all the variations laid out above, it might seem that there’s no real definition of what is or isn’t a Trapper. Well, a Trapper definitely is a jack knife, meaning the blades fold out of one end (unlike a pen style multiblade knife, in which the blades open from different ends), and the end the blades come out of should definitely be smaller than the butt end of the handle. A Trapper definitely doesn’t have a straight edged blade, like a sheepfoot or wharncliffe, as its only main blade. Within those parameters, a wide array of knives can be considered Trappers. Kind of like some other things, it’s something that’s difficult to define but you know it when you see it. Another great way to know if a knife is a Trapper is if the company that made it calls it a Trapper!

A great knife to use while camping or to cut hot dog sticks for a fire

The Trapper pattern is somewhat nebulous, but even still it holds a significant place in the American cutlery tradition. Every kind of Trapper has been made, even at least one modern flipper opening version! If you like traditional pocket knives you’re sure to be able to find a Trapper that suits your particular aesthetic and practical tastes.

A couple single blade Trappers

If you’d like to get yourself a Trapper I have some suggestions. If you’d like the nicest production Trapper you can get currently, and don’t mind carbon (non-stainless) steel, you should go with the Great Eastern Cutlery #48 Slim Dog Leg. Great Eastern Cutlery made knives tend to sell out relatively quickly, but they’ve been doing larger runs to try to better meet demand and there are a good number of these left on dealers’ sites. You can find some at Blue Creek Cutlery, my most often patronized GEC dealer. Ken is a good guy and has good service, don’t hesitate to ask him any questions you have before purchase. You can also find some, including some other handle materials, at DLT Trading. Those Trappers from GEC are USA made in small batches in Titusville PA and heirloom quality but also great users. If you’d like a more modern stainless steel (although not a super steel, using 8cr13mov) and don’t mind your knife being made overseas, the Sowbelly Improved Trapper from A.G. Russell is also a great option. These have a little less character and might not be quite as well finished but they are still really well made and good looking knives, and they’re less expensive than the GECs. If you’d like a less expensive option than the GECs but want to stick with good ol’ Made In U.S.A. quality, Case knives are made in Bradford Pa and aren’t quite as well fitted or finished as GEC but still make great using knives (and many people also collect them). Case offers a multitude of Trapper options: Full Size Stainless Steel, Mini Stainless Steel, Large Stainless Steel Single Blade with Clip and Thumb Stud, Slimline with option for Stainless or Carbon Steel, Full Size Carbon Steel. Another good option that’s really easy on the wallet is going with a Rough Ryder. These are made overseas and sometimes have some issues, but they’re definitely high enough quality to make good users and often are really nice looking for the price, which is significantly lower than any of the above options. Smoky Mountain Knife Works owns the Rough Ryder brand and carries a wide variety of Trappers in different shapes, sizes, and handle materials. Finally, if the modern style trapper I mentioned piqued your interest you can the Boker Plus Urban Trapper at this link.

Some links in this article are affiliate links. That means that if you click them and purchase the product you won’t pay any more than you normally would, but I get a commission from the sale. This is just a way for you to support Knife Thoughts. Be sure to try my discount codes “KnifeThoughts” or “KT10”!

I sincerely thank you for your time, support, and interest! Don’t forget to tell your friends about KnifeThoughts.com, subscribe via email, and share this article on social media. You can find Knife Thoughts on YouTube where I have hundreds of knife videos, as well as on Instagram and Facebook! You can find all my latest links at LinkTr.ee/KnifeThoughts